Half Bathroom Remodeling in Scottsdale turns the smallest room in your house into the one guests remember. We handle powder rooms and half baths from tear-out to final caulk line, with plumbing, electrical, tile, and paint under one licensed crew. If your vanity is warped, your grout is stained, or your fixtures date back two decades, we can have a clean, code-correct half bath renovation Scottsdale homeowners actually use again.
Half Bathroom Remodeling in Scottsdale is the trade of rebuilding a toilet-and-sink room from the studs out. That means pulling the old vanity, resetting the toilet flange, replacing the shutoff valves with PEX or copper piping, hanging cement backer board, and setting porcelain tile over a waterproofing membrane. We swap dated fixtures for Kohler or Moen, wire a GFCI outlet, and finish with moisture-resistant paint. No tub, no shower pan, just the essentials done right.
Most Scottsdale half baths sit off a hallway or laundry room and get ignored for 20 years. Hard water stains etch the faucet, the exhaust fan quits, and the vanity cabinet warps from a slow supply-line drip. A half bath renovation Scottsdale homeowners schedule with us usually starts because a guest noticed the smell or the running toilet. We fix the cause, not just the finish.
A standard half bath package covers everything from tear-out to the final walkthrough. Add-ons like heated floors, custom cabinetry, or relocating the toilet are quoted separately so you can see the cost before you decide. Here is what is in the base scope.
We remove the old vanity, toilet, flooring, and any damaged drywall, then haul it all away. The subfloor gets inspected for rot and soft spots. If we find water damage under flooring, we show you the extent and the repair cost before we rebuild.
New PEX or copper piping replaces the old supply lines, and we reset the toilet flange to the correct height. Shutoff valves get swapped for quarter-turn ball valves. We test every joint under pressure before the wall closes.
A GFCI outlet goes in to NEC standards, and we install an exhaust fan sized for the room. LED lighting on a dimmer is standard. If the existing circuit cannot carry the load, we run a new line from the panel.
Cement backer board and a waterproofing membrane go behind every tile surface. We set porcelain or ceramic tile to ANSI A118 standards, grout with epoxy, and seal corners with silicone caulk. Floor tile is included in the base scope.
We set the vanity cabinet level, mount the countertop, drop in the sink, and install the faucet. A new toilet with a wax ring and shims finishes the room. Kohler, Moen, Delta, and American Standard are all options we stock or order.
Moisture-resistant drywall gets taped, floated, and painted with moisture-resistant paint. Baseboards, a mirror, and any hardware go back on last. We do a full function test on every fixture and walk the room with you before we pack up.
We walk your half bath, measure the vanity run, check the toilet flange height, and test the shutoff valves. You get a written scope and a fixed price the same day. Most estimates take 30 to 45 minutes. We also note whether the wall behind the vanity shows old water staining.
Day one is tear-out. We pull the vanity, toilet, flooring, and any damaged drywall, then cap the lines. A pipe wrench and plumber's snake clear the drain if it is slow. We inspect the subfloor for rot and replace any soft sections before framing new blocking for the vanity cabinet.
We run new PEX piping, set the toilet flange, and install the GFCI outlet and exhaust fan. A laser level keeps the vanity and mirror plumb. Rough-in inspection happens before anything gets closed up, which is why we schedule it early. This stage usually runs two to three days.
Cement backer board goes up, then a waterproofing membrane in wet zones. We set porcelain tile with a notched trowel and cut edges on a wet saw, following ANSI A118 standards. Epoxy grout goes in the joints, silicone caulk seals the corners, and the walls get moisture-resistant paint.
We hang the vanity cabinet, set the quartz countertop, drop in the sink, and mount the faucet. The toilet gets a new wax ring and shims. We test every line, run the fan, and check the GFCI. You walk the room with us before we call it done, usually day seven to ten.
We walk your half bath, measure the vanity run, check the toilet flange height, and test the shutoff valves. You get a written scope and a fixed price the same day. Most estimates take 30 to 45 minutes. We also note whether the wall behind the vanity shows old water staining.
Used to cut porcelain tile, ceramic tile, and natural stone to size. Clean cuts mean tight grout lines and no chipped edges around the toilet flange or door casing.
The notched trowel controls mortar thickness and coverage. The grout float presses epoxy grout into the joints evenly, which prevents voids that later crack or stain.
The laser keeps the vanity, mirror, and tile rows plumb and level. The stud finder locates framing for grab bar blocking and cabinet screws, so nothing pulls loose from drywall alone.
The moisture meter confirms the wall cavity is dry after a leak repair. The plumber's snake clears slow drains before we close the floor, so you are not chasing a backup later.
The pipe wrench breaks loose old supply fittings during demo. The caulking gun lays a clean silicone caulk bead at the sink rim, tile corners, and base of the toilet.
The multi-tool cuts drywall and trim in tight corners without damaging adjacent surfaces. The screw gun sets backer board and cabinet screws at consistent depth.
A 5x6 powder room with a warped vanity, cracked ceramic tile, and a toilet that ran constantly. The exhaust fan had not worked in years, and the wall behind the vanity showed old water staining from a slow supply-line drip.
After: We replaced the supply lines with PEX, rebuilt the damaged wall section, and set new porcelain tile over a waterproofing membrane. A new quartz countertop, Moen faucet, and American Standard toilet finished the room. Total time: eight working days.
Book this service →A rental half bath with a chipped vanity, stained grout, and a GFCI outlet that tripped every time the tenant plugged in a hair dryer. The unit was vacant and the owner needed it ready for a new lease in two weeks.
After: We staged materials before demo, installed a new vanity cabinet and quartz top, re-grouted with epoxy, and replaced the GFCI outlet to NEC standards. The room was photo-ready in nine working days, ahead of the lease date.
Book this service →
A half bath off the guest room needed to serve aging parents. There was no shower, the toilet was standard height, and the exhaust fan was undersized for a wet room. The doorway was narrow and the lighting was a single overhead bulb.
After: We added a tiled shower with a waterproofing membrane, installed grab bar blocking and a comfort-height toilet, and upgraded the exhaust fan and LED lighting. The GFCI outlet was relocated for easier access. The project ran 14 working days.
Book this service →Small rooms hide big problems. These are the issues we see most often when we open up a Scottsdale half bath, and what it takes to fix them right.
Ask a pro →We replace the supply lines with PEX or copper piping, dry the cavity, and check with a moisture meter before closing the wall. Then we set a new vanity cabinet on blocking, so it stays level and dry.
We remove the failing grout, treat the hard water stains, and re-grout with epoxy grout that resists mineral buildup. A silicone caulk line at the wall joint keeps water out of the perimeter.
We install a correctly sized exhaust fan, vent it outside through the roof or wall, and wire it to a timer switch. That pulls moisture out during use and keeps the room dry between visits.
We trace the circuit, correct the fault, and install a new GFCI outlet to NEC standards. We test it under load before we leave, so you know it holds.
Most half bath remodels in Scottsdale run $6,500 to $14,000 in 2026, depending on whether we move plumbing and what finishes you pick. A basic refresh with a new vanity, toilet, tile floor, and paint lands near the low end. Adding quartz countertop, custom cabinetry, or relocating the sink pushes it higher. We give you a fixed written price after the on-site measure.
A full half bath renovation Scottsdale homeowners book with us includes tear-out, new PEX or copper supply lines, a reset toilet flange, cement backer board, porcelain or ceramic tile, a vanity cabinet, countertop, sink, faucet, GFCI outlet, exhaust fan, and paint. We handle permits and inspection. Add-ons like heated floors or a wall-hung vanity are quoted separately.
Plan on seven to ten working days for a standard half bath, from demo to walkthrough. Plumbing and electrical rough-in takes two to three days, tile and finish another three to four, and set day is usually one. If we relocate the toilet or sink, add two days. We give you a day-by-day schedule before we start.
Yes, if you move plumbing, add or relocate electrical, or change the ventilation. Cosmetic swaps like a new vanity or faucet usually do not require one. We pull the permit through the city and meet the inspector at rough-in and final. Working without a permit can stall a home sale and cost more to correct later.
One call gets you an on-site measure, a fixed written price, and a start date. We are licensed, insured, and bonded, and we answer the phone seven days a week. Call +1 855-612-4434 and let's get your powder room off the to-do list.
Get Free Estimate +18556124434 →Call +1 855-612-4434 or email info@scottsdalebathroomremodeling.com and we will get back to you the same business day. We answer the phone Monday through Friday, 8:00 to 18:00, and we schedule walkthroughs across Scottsdale and Maricopa County within a few days. Bring your wish list and your budget.