Old Top Removal
We shut off the water, disconnect the faucet and drain, and lift the old counter off the vanity. The cabinet gets checked for warping, soft wood, or water damage while the top is off. Debris is bagged and hauled away the same day.
Bathroom Countertop Installation Scottsdale AZ means a counter that fits your vanity, your sink, and your daily routine. We template, fabricate, and set quartz, granite, and marble tops for homeowners across Scottsdale, Arizona - from 85251 condos to 85255 master baths. If your old laminate is peeling, your tile grout is stained, or you are mid-remodel and need the top measured this week, we handle the whole job: tear-out, plumbing disconnect, fabrication, and a clean, level set.

Bathroom Countertop Installation Scottsdale AZ is the measured, fabricated, and sealed replacement of a vanity top - the slab, the sink cutout, the backsplash, and the faucet holes - done so the surface sits flat, drains correctly, and survives daily use. We pull the old top, check the vanity cabinet for warping or water damage, cut the new slab on a wet saw, and set it on a fresh bead of silicone. Sink cutouts are drilled and polished, edges are eased or bullnosed, and the faucet and drain get reconnected before we leave.
Most Scottsdale calls come from two places: a 1990s vanity with failing laminate and a cracked cultured marble top, or a homeowner upgrading to quartz during a larger bath refresh. Hard water stains etch cheap tops fast here, and grout lines on old tile counters trap soap scum. If you are pricing bathroom countertop replacement Scottsdale wide, we can usually template within a few days and have the slab ready in one to two weeks depending on material availability.
Every counter job we quote covers the full path from tear-out to test. Here is what is in the scope, so you know what you are paying for before we start.
We shut off the water, disconnect the faucet and drain, and lift the old counter off the vanity. The cabinet gets checked for warping, soft wood, or water damage while the top is off. Debris is bagged and hauled away the same day.
A laser level and digital template kit capture the exact cabinet width, sink cutout, faucet spread, and backsplash height. We mark the drain location too, so the new top drops in without shimming or re-drilling.
Your slab is cut on a wet saw, the sink cutout is polished, and the edge is shaped to the profile you picked - eased, bullnose, or a mitered build-up. Quartz and granite both get a dry-fit check before they leave the shop.
The new top is set on a fresh bead of silicone, leveled, and sealed at the wall and splash joints. We use silicone caulk in wet areas and keep the sink rim watertight so nothing drips into the cabinet below.
Faucet, supply lines, and drain get reconnected and tested. We run the water, check for drips at the base and the shutoffs, and confirm the drain flows. If a shutoff valve is seized, we flag it before it becomes a leak.
You call or text, send a few photos of the vanity and sink, and tell us the material you are leaning toward. We ask about the cabinet width, the sink type, and whether the plumbing has leaked before. Within a day you have a ballpark number and a templating window.
We come out with a laser level and a digital template kit, check the vanity for level and any warping, and mark the sink cutout, faucet spread, and backsplash height. This visit takes about 45 minutes. You pick the edge profile and confirm the slab.
Your slab is cut on a wet saw, the sink cutout is polished, and the edges are shaped to the profile you chose. Quartz and granite both get a dry-fit check before they leave the shop. Turnaround runs five to ten business days for most materials.
On install day we shut off the water, disconnect the faucet and drain, and lift the old top. We check the cabinet for soft wood or mold, then set the new slab on silicone, level it, and reconnect the plumbing. Most single-vanity jobs take two to three hours.
We run a bead of silicone caulk along the wall and backsplash, let it skin, then test the faucet and drain for leaks. The counter gets wiped down, the old top gets hauled away, and you get a walkthrough before we pack up. No debris left in the driveway.
You call or text, send a few photos of the vanity and sink, and tell us the material you are leaning toward. We ask about the cabinet width, the sink type, and whether the plumbing has leaked before. Within a day you have a ballpark number and a templating window.
Cuts quartz and granite slabs with a water-cooled blade so the edge stays chip-free and the dust stays down. Every sink cutout and edge cut runs through it.
Checks the vanity for level before templating and confirms the new top sits flat. A rocking counter opens the caulk line and leaks.
Captures the cabinet width, sink cutout, faucet spread, and backsplash height to the fraction. This is what makes the slab drop in without shimming.
Lays a consistent bead of silicone caulk along the wall and splash joints. A clean bead is the difference between a watertight seal and a slow leak.
Loosens the supply lines and drain fittings during disconnect and tightens them on reconnect. We check the shutoff valves while we are in there.
Cuts the old caulk line and frees the old top from the cabinet without gouging the vanity frame or the drywall behind the splash.

A 1990s vanity in 85258 with a cracked cultured marble top and a stain ring around the faucet. The caulk line behind the splash had failed, and the cabinet top was damp.
After: We pulled the old top, dried and sealed the cabinet, and set a white quartz slab with an undermount sink and a 4-inch splash. Install took two and a half hours. The new top has no stain and no leak.
Book this service →
A master bath in 85255 with a faded cultured marble double vanity. The sinks were drop-in, which trapped grime around the rim, and the faucets were original builder-grade.
After: We templated for two undermount sinks and set a granite top with a bullnose edge and a 6-inch splash. New faucets went in the same day. The counter added usable space and the room photographed like a remodel.
Book this service →
A small powder room near Old Town with a 24-inch laminate top and a scratched drop-in sink. The laminate had swollen at the front edge from years of water exposure.
After: We set a compact quartz top with an undermount sink and a slim 2-inch splash. The job took under two hours. The room now reads current, and the swollen edge is gone.
Book this service →Most vanity tops fail the same way. Here are the four calls we get most often and how we handle them.
Ask a pro →We pull the old top, inspect the cabinet, and set a new quartz or granite slab with a polished sink cutout. You get a non-porous surface that will not stain from toothpaste or hard water.
We remove the old caulk, dry the joint, and re-seal with silicone caulk after the new top is set. If there is drywall damage, we patch it before the splash goes back on.
We reset the sink on the new counter with proper clips and silicone, then test the drain and supply connections. If the old cutout is oversized, the new slab gets a fresh, correctly sized opening.
We check the cabinet while the top is off. If the base is sound we shim and level it. If it is soft, we quote a cabinet repair or replacement before setting the new counter, so the slab sits flat.
Most single-vanity jobs run $900 to $2,800 installed, depending on material and size. A 36-inch quartz top with an undermount sink and a 4-inch splash sits near the lower end. Granite with a double sink, a taller backsplash, and a complex edge profile pushes toward the top. Templating, fabrication, tear-out, plumbing reconnect, and haul-away are all in that number. We give you a written quote before we cut anything.
Quartz is the best all-around choice for Scottsdale because it shrugs off hard water and needs no sealing. Granite is a close second if you want natural stone and do not mind an annual sealer coat. Marble looks great but etches from toothpaste and citrus, so we steer most families away from it in a kids' bath. Cultured marble is the budget option and works fine in a guest or powder room.
Plan on one to two weeks from template to set. Templating takes about 45 minutes, fabrication runs five to ten business days for most quartz and granite, and install day is two to three hours for a single vanity. If you pick an in-stock slab, we can sometimes compress that to under a week. Double vanities add an hour or so on install day.
No. The vanity cabinet stays in place. We shut off the water, disconnect the faucet and drain, and lift the old top off the cabinet. That is faster, cheaper, and avoids disturbing the tile or flooring around the base. We do check the cabinet for warping or water damage while the top is off, and if the base is soft we show you before setting the new slab.
Send us a photo of your vanity and we will give you a ballpark number the same day. Arizona ROC licensed, warrantied install, and a clean haul-away when we are done. Call now and get on the template schedule this week.
Get a Free Quote +18556124434 →Call +1 855-612-4434 or email info@scottsdalebathroomremodeling.com and we will get back to you the same business day. We answer the phone Monday through Friday, 8:00 to 18:00, and we schedule walkthroughs across Scottsdale and Maricopa County within a few days. Bring your wish list and your budget.